Nmap problem

I ve tried to use nmap in many ways (below), even nmap -v hasnot returned me right.
what could be the problem?

root@kali:~# nmap 35.227.58.252
Starting Nmap 7.70 ( https://nmap.org ) at 2018-05-21 22:23 EDT
setup_target: failed to determine route to 35.227.58.252
WARNING: No targets were specified, so 0 hosts scanned.
Nmap done: 0 IP addresses (0 hosts up) scanned in 0.06 seconds
root@kali:~# nmap -v -A 192.185.214.135
Starting Nmap 7.70 ( https://nmap.org ) at 2018-05-21 22:25 EDT
NSE: Loaded 148 scripts for scanning.
NSE: Script Pre-scanning.
Initiating NSE at 22:25
Completed NSE at 22:25, 0.00s elapsed
Initiating NSE at 22:25
Completed NSE at 22:25, 0.00s elapsed
setup_target: failed to determine route to 192.185.214.135
NSE: Script Post-scanning.
Initiating NSE at 22:25
Completed NSE at 22:25, 0.00s elapsed
Initiating NSE at 22:25
Completed NSE at 22:25, 0.00s elapsed
Read data files from: /usr/bin/…/share/nmap
WARNING: No targets were specified, so 0 hosts scanned.
Nmap done: 0 IP addresses (0 hosts up) scanned in 0.87 seconds
Raw packets sent: 0 (0B) | Rcvd: 0 (0B)
root@kali:~# nmap 192.168.0.9
Starting Nmap 7.70 ( https://nmap.org ) at 2018-05-21 22:26 EDT
setup_target: failed to determine route to 192.168.0.9
WARNING: No targets were specified, so 0 hosts scanned.
Nmap done: 0 IP addresses (0 hosts up) scanned in 0.06 seconds

It looks like the ips you specify are not reachable. Can you ping them?

also having problens with ping.
Take a look at my ifconfig, I do not see my IP, something weird here.
root@kali:~# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
ether 00:0c:29:8c:22:a5 txqueuelen 1000 (Ethernet)
RX packets 237 bytes 79998 (78.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::20c:29ff:fe8c:22af prefixlen 64 scopeid 0x20
ether 00:0c:29:8c:22:af txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 621 bytes 110334 (107.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10
loop txqueuelen 1000 (Local Loopback)
RX packets 20 bytes 1200 (1.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 20 bytes 1200 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

There is a problem with your network card config.

you seem to be in IPv6 instead of IPv4. maybe it’s the problem there